Alan

Ribstabsheart:  To save time and excessive stone wear, I file the edge flat, down to the bottom of the deepest defect, using one of the finer diamond stones – like the 800 grit.  How long you need to work and edge is directly related to the amount of steel you have to remove and this process very quickly removes a lot of that steel.  Having do…[Read more]

PM sent

I thought about using a dot of silicone sealer to cement the sockets in place. The dried excessive could easily be trimmed away with a razor knife.

The little white “keeper” balls need to be saved to reposition them whenever the ball-end guide rods are removed. These “keeper” balls hold the delrin pivot sockets in place so they won’t fall out and get lost.

All I know is the original WEGO, (WE50) was an extruded base. This new WE60 is machined. The WE60 is a single, stand alone model, it is not upgradeable.  Another, better optioned model, based on this compact format is slated for release this fall around Nov.

First, on your microscope, I wanted to say: all the USB scopes I have ever used have both low and high-power magnification.  Now you’re turning the fine focus just a little either way to focus the image at the low power you are viewing with. Try to turn the fine focus knob past where it goes out of focus, then as far as it goes. Then it should…[Read more]

I see from your photo your working with a WE100, not a WE120. Both models the WE100 & WE120 utilize the same “standard” style vise. The standard vise is a two-piece vise with the left side fixed while the right side floats and is attached to the fixed side by the upper screw screw. The upper screw tightens or closes the vise on the knife. Then the…[Read more]

The first visual aide I used was a lighted jewelers loupe. Like you, I quit using it when I realized just how close my face was to the sharpened knife edge. Now I use this usb handheld scope with a laptop:

I work start to finish at the same set…[Read more]

Looks pretty good. I’d work the edge a little more. It looks like there’s gaps in the burr or small edge chips that should easily be removed with a little more effort.  If the chips are small and numerous across the edge I’d work at it until most of the shallower ones are sharpened out. If there’s only a few larger or deep chips across the entire…[Read more]

To private message click the userame anywhere it is showing in blue color in any boxes of the thread. This will direct you to the W.E. messaging feature. Then click “private message” at the top menu. At the upper right corner of the opening Forum page there is a round white number “0”. This will become blue and the number will change to reflect…[Read more]

The WE120 is your tool. Use it how you may. For situations with very wide angles I replaced the pointed thumb screws with flat ended nylon thumb screws (10-32). These nylon thumb screws will lock the mini “L” brackets in position simply compressing against the flat sides of the square bar. If you message me with your email address and mailing…[Read more]

Welcome to the W.E. Forum Ribstabsheart.

It sounds as though you’re putting in the effort and you have a good understanding of what you’re doing. You included a lot in your post. I’ll try to break it down to address each issue.

The W.E. is basically a bench vise that clamps and holds knives vertically allowing us to move the sharpening stone…[Read more]

I mounted my new WE60 on the base from my WE120.

The forum is not dead, it’s just something you find inconvenient to use on your small format devices.  That doesn’t reflect on our forum, it’s function, quality or contributions by members.  I agree that this older forum format lends itself to devices that are more typing friendly.  More so, a forum is for those who don’t mind writing a full se…[Read more]

??

PM sent

The WE60 is not upgradeable:

WE60 was released yesterday. Now listed on the W.E. website $275.

Clay has said to look for the release of the other models this fall, possibly Nov.

Here’s another pre-release blog for the WE60 model. This one was published by the Australian Wicked Edge Dealer, Zanvak:

https://zanvak.com.au/blogs/all-blogs/wicked-edge-go-we60-series-portable-knife-sharpener