James

Welcome to the W.E. forum Steve.

Can you elaborate on what specific subject matter you are looking for in a data base.  The knowledge base has quite a bit of information.  Some of the subjects discussed may include a data base.

https://support.wickededgeusa.com/portal/en/kb/articles/knife-sharpening-settings-submitted-by-customers

000Robert:  That’s the crux of it right there.

If we had a mission statement here for the Wicked Edge Forum I think it would be: we are here to help educate W.E. users so they can learn how to use or operate their sharpeners well.  To make their sharpening experience productive, successful, and enjoyable.

We help by sharing our user e…[Read more]

I did not misconstrue your post thinking you were meaning, directing to, or talking about me.

What I take exception with is your use of “most people”.  I think the issue described of damaged edge steel as the result of bad heat treatment or overheated edge grinds is far less common then you’re choice of words suggests it to be.

I maintain…[Read more]

I’ve participated and contributed to this forum for several years now to help many Wicked Edge users learn how to sharpen their knives with their W.E. Systems.  I’m not sure who the “most people with problems with their new knife edges” are that 000Robert is referring to.

I propose for these people that have to remove and reprofile their new…[Read more]

I use alternating side scrubbing strokes, as the first sharpening strokes, with each and every grit sharpening mediums, on every knife I sharpen or touch up.  The aggressiveness I use and the amount of steel I remove is intentional and is determined by my applied pressure and the force employed with the scrubbing strokes against the knife edge.   …[Read more]

Couple things to look at:

Are your stones broken in yet?  It takes a minimum of ten knives to just get them started on the way.  Are you using each grit long enough.  Longer is better then not long enough.  You can not over do it.

Consistency is key.  Strive for consistent finger position on the sharpening stones and consistent finger pres…[Read more]

KMe,  every part of the WE130 can possibly contribute to these slight differences you’re seeing.  The tolerance of the screw holes used to mount the square bar and the screws that secure the vise, each impart a little to these observed differences.

To tell you the truth all that doesn’t matter.  What matters is how you position your guide rod ba…[Read more]

KMe,  if you are simply trying to determine how close to equal the guide angles are from side to side.  That is to determine if your WE130 is square. You can position the guide rods how you described in your original post using the same indent hole positions with the micro-adjuster screws backed-in all the way on both sides.

Then with something l…[Read more]

Welcome to the W.E. forum, KMe.

To calibrate the guide rod angles is to position them so their positions correlate with the readings of an instrument.  In our case the instrument is a properly zeroed-out digital angle cube.  Then the guide rods are calibrated “relative” to this instrument, this angle cube.

What you’re describing is simply p…[Read more]

Joshua, There are many YouTube videos that you can watch that may help you.

Here’s a Knife Sharpener and a Wicked Edge user you might check out: https://www.youtube.com/channel/UCp16WaVffmeglWvW-fDQ4dQ

He has many worthwhile videos including knife sharpening with belt sanders/grinders.

John, we houden dit forum in het Engels, maar ik zal proberen te helpen. Allereerst zou ik willen voorstellen dat u een lokale Wicked Edge-dealer in Nederland zoekt voor hulp bij een reparatie of vervanging.

Als u geen lokale W.E. dealer in uw buurt, neem dan contact op met de Wicked Edge-klantenservice. Ze kunnen u helpen met uw probleem. Het is…[Read more]

Your whole premise is wrong…The diamonds aren’t performing.  They’re inert.  They are simply sorted somewhat by size then attached on a steel flat bar with a nickel plating.  Then they are dragged across the knife’s steel alloys in order to scratch the bevels.  The diamonds don’t do anything.  The steel matrix that is being scratched and goug…[Read more]

I did prove it… to myself.  That’s all the proof I need.  I do not have to prove anything to you, 000Robert.  The way something “seems it should be”, to you, is not necessarily how it is in reality.

I’m a solutions guy.  When I have difficulty sharpening a knife with the W.E. diamond stones, first I try to change up or adapt my sharpening tec…[Read more]

Welcome to the Wicked Edge forum, Bryce Herbst.

I’m a proponent of using the sharpening medium that will sharpen your knife’s steel the best.  Your fears of damaging those steels are well founded and based in real experiences.   Harder steels such as you related, harder than HRc 59-60 can be more on the brittle side and may suffer damage in th…[Read more]

Making use of blue painters tape allied to the knife’s sides will protect the blade steel from unwanted scratches that can and will happen during sharpening.  Also wrapping the knife’s slot and the hinge mechanism will keep steel dust and diamond abrasive out the works.

New stones as you use then during the break-in period will slough off loose…[Read more]

Welcome to the Wicked Edge forum Wetworx:

For the new users of Wicked Edge Precision Sharpeners, (WEPS), it’s recommended you start learning to sharpen with your WEPS while shatpening your beater knives or junk knives.  It’s best to save your good knives like your edc, you mentioned above, until your sharpening stones are broken in.  This is u…[Read more]

Here are photos from the end of working with each grit when I was ready to move up to the next finer DMR stone.

Here is the 80 Grit:

This is the next grit in the sequence, 250 grit:

I’d say this DMR 250 grit scratch pattern is very similar to the a well broken in W.E. 200 or 400 grit stone.

This next photo is the DMR 650 grit:

I find t…[Read more]

I finally used these friction disc on my micro angle adjusters last night.  It was the first real sharpening test.  The discs hold and lock very tightly.  When the thumb wheel is locked down on the disc it grabs tight and holds fast.  There’s no noticeable travel, rolling or sliding against the disc as the thumb wheel locks the adjuster set…[Read more]

I finally made the time to use the Resin Bonded Diamond Matrix Stones for the first knife, last night.  I hadn’t made the time to use them yet.  My barter guy who trades me Gulf of Mexico fish, (snapper and grouper) for sharpening knives showed up with an awful knife and two bags of fresh frozen delight.

The knife was an absolute disaster.  Fr…[Read more]