Alan
-
tcmeyer replied to the topic Carbon Fiber Guide Rods in the forum MODS 2 months, 1 week ago
Mcmaster Carr sells carbon fiber rods which you could thread yourself if you get a 1/4″-28 die and die handle.
Carbon fiber rods are quite expensive at $50 plus shipping for a 48″ length.They also sell rods in Garolite, which I believe is the equivalent of G10 and has some lubricity to it. It sells for $16 per 48″ rod.
I made my rods from…[Read more]
-
Marc H replied to the topic Carbon Fiber Guide Rods in the forum MODS 2 months, 1 week ago
The only replacement guide rods can be purchased from WE:
-
Marc H replied to the topic Carbon Fiber Guide Rods in the forum MODS 2 months, 1 week ago
I’m using one of a couple sets that are being prototype.
https://www.facebook.com/share/v/gSi2Muj2REi8CkQp/?mibextid=oFDknk
-
Marc H replied to the topic Wicked Edge Buyer's Guide – Fall and Holiday Season 2023 – WE60, WE66 & Gen4Pro in the forum Product Announcements 2 months, 1 week ago
IMO: The $200 micro-angle adjusters included with the WE66 are a convenience you’ll either enjoy or regret forever.
The WE66 micro-angle adjusters are unmatched in dial-in precision adjustability.
-
tcmeyer replied to the topic Discordant micron ratings in the forum Main Forum 2 months, 3 weeks ago
I’ve been using a micron/mesh chart that was published by Advanced Abrasives about 10 years ago. It’s always worked for me and seems to match up very close to the chart on the WE grit/micron list taken from the WE support list.
I think it’s important to note that we’re not publishing a set of standards for the industry – just a guideline to use…[Read more]
-
Marc H replied to the topic Stabil-Rizer Large, long and flexible knife Adapter in the forum MODS 2 months, 3 weeks ago
Here’s a narrow bladed Rapala filet knife clamped in WE130 equipped with a WE130 Stabil-Rizer kit:
-
Marc H started the topic Stabil-Rizer Large, long and flexible knife Adapter in the forum MODS 2 months, 4 weeks ago
Stabil-Rizers are the latest collaboration between Doug P. (airscapes) and Marc H (MarcH). The Stabi-Rizer is an easy-on, easy-off adapter to provide vertical and lateral stability to large, long and flexible knives. Enhances low angle accessibility. Compatible with all WEPS modes. (In final ß-testing.) Availability and pricing TBD.
-
tcmeyer replied to the topic Annoying purchasing experience in the forum Welcome Mat 3 months ago
I’ve run into this problem of abnormally large clusters of diamond grit a few times before. In instances where the cluster is aligned parallel to the stone, they are really hard to knock off and the normal process of breaking them in doesn’t do it. On particularly hard steels like my ZDP-189’s, they can produce some really nasty chips. I fo…[Read more]
-
Marc H replied to the topic Discordant micron ratings in the forum Main Forum 3 months, 1 week ago
I’m wondering or trying to remember if those previous micron ratings we’re the visual scratch depth measurements done with high power photography.
-
wickededge replied to the topic Annoying purchasing experience in the forum Welcome Mat 3 months, 1 week ago
Jeff,
That’s terrible all the way around. The only good thing is the quality of your photos… I’ve asked our Customer Success manager to reach out and try to fix this for you more quickly.
-
Marc H replied to the topic Annoying purchasing experience in the forum Welcome Mat 3 months, 2 weeks ago
WE will replace.. You may try to run the stone bump against the spine of jumker knife. The hard surface contact often knocks off the high spot.
-
Marc H replied to the topic Gen 3 Pro for sale, lightly used. Many extras in the forum Main Forum 3 months, 2 weeks ago
PM sent
-
Marc H replied to the topic Gen 3 Pro for sale, lightly used. Many extras in the forum Main Forum 3 months, 2 weeks ago
Nice setup. You may want to post to:
-
Marc H replied to the topic Newbie with a question in the forum Welcome Mat 3 months, 3 weeks ago
Welcome to the W.E. Forum, Paul.
Call W.E. or better, submit a support ticket. If they have the replacement part, W.E. will provide it.
-
tcmeyer replied to the topic 3D printed Custom handles in the forum Want to Sell 4 months, 1 week ago
Sorry I’m late on this one, but here’s one tidbit I have to share:
If the long bore diameter is larger than the rod diameter, you’ll want rods which are extra long. If you slide the handle high enough to have the rod drop out of the upper bushing, you’ll see some angular error and if the bushing are a tight fit, you’ll see some binding between…[Read more]
-
Marc H replied to the topic Newbie introduction 🙂 in the forum Welcome Mat 4 months, 1 week ago
Here are two aditional sources for W.E. users:
https://www.facebook.com/groups/683248253138189/?ref=share
and
https://www.facebook.com/groups/2039273959688449/?ref=share
-
Marc H replied to the topic Newbie introduction 🙂 in the forum Welcome Mat 4 months, 1 week ago
Welcome to the W.E. Forum and community, Evan.
-
Marc H replied to the topic New vise jaws in the forum Cooking 4 months, 2 weeks ago
Try to shop thrift stores and flea markets
-
Marc H replied to the topic FOR SALE – GEN3 PRO BRAND NEW IN CASE WITH ALL ACCESSORIES in the forum Want to Sell 4 months, 2 weeks ago
Robert, welcome,
When you’re able, shop you’re model new today from WE.
https://www.facebook.com/groups/683248253138189/permalink/735133157949698/?mibextid=Nif5oz
-
Marc H replied to the topic New vise jaws in the forum Cooking 4 months, 2 weeks ago
Yes, needs to be in a roller case. I just installed those same new “V2” jawset on my gen3 vise. We’ll learn how we like the new jaws together.
- Load More