Robert Garrity
Forum Replies Created
-
AuthorPosts
-
03/24/2013 at 10:08 am #10443
yeah I was placing the knife too far forward at first, it also makes it hard to get the heel of the blade. I did the sharpie after the first 2 stones, and was using my 20x loop to see if I was apexing. I used the sand paper trick after the 1000grit stone to get the polish and stropped it about 3 times as long as the first 2 knives I did. Another beater that I keep in my work life vest as an emergency blade I thined out the tanto tip so that was another good learning experience, I will probably try to keep my higher end tantos a little fatter at the tip, but at least it cuts better now, I will not be stabbing with this knife!
03/23/2013 at 7:11 am #1042103/23/2013 at 7:00 am #10420We’ll I am still waiting for the paper to just split in half in fear as it moves closer to the edge.
03/23/2013 at 6:50 am #10419Thanks Geocyclist I just got my we today and sharpened 2 beater knives and got them reasonably sharp but no where near hair whittleing, which is what I’m after. I was thinking to myself that man my sharpmaker does a better a job than this and this cost me 10 times what that did. Can’t wait for that wow moment!
Geocyclist is exactly right. You’ll be seeing regular improvement with your edge as your stones break in and your technique builds. I hope you’ll continue to post your results.[/quote]
Thanks Clay on my third knife today got to just barely hair whittleing so its progressing. The edge looks so sweet never got one looking so nice before. Will upload a pic.
03/22/2013 at 2:10 pm #10410Welcome to the forum.
About China and the US. I work in manufacturing and see both great stuff and crap come from both China and the US. I like to buy from the US. But I don’t blindly buy US just because of the tag. When money allows I buy the best where ever it comes from and take care of it. IMHO WEPS is the best.
With respect to WE or anything being a good product I believe it is not just quality, but also design and customer service. In these areas you won’t be disappointed. More important than all this is passion. I see a passion for this product in WE. Not that they just see this as product to produce. In the end passion drives everything that is important.
DO NOT be disappointed with your first or 5th knife. A.) It takes 5 – 10 or so knives to break in the diamond stones. The first knife will probably not blow your mind. B.) Your technique will improve. It took me to about my 7th knife to finally say I had a Wicked sharp edge, with mirror polish, even bevels, etc.. My first two knives I was worried I had wasted my money. By knife #5 I wasn’t worried any more about if I had wasted my money on the WE. Your first two knives or so should be ones you don’t care much about or worry about messing up.
Thanks Geocyclist I just got my we today and sharpened 2 beater knives and got them reasonably sharp but no where near hair whittleing, which is what I’m after. I was thinking to myself that man my sharpmaker does a better a job than this and this cost me 10 times what that did. Can’t wait for that wow moment!
02/16/2013 at 12:36 pm #9546Check the accuracy of your angle cube the one they sell with the system is only accurate to +- 0.2 deg. Harbor freight brand Pittsburgh angle gauge is only accurate to +-0.3 deg. if your within that tolerance you should be good just move it and check again and it may settle out but a full degree is weird. The hundredths of a degree (0.01) spot is useless.
So what is the general consensus on finding an angle with the angle gauge?
Specifically, when I zero the gauge, if I get the angle, move the stone to vertical and check again, I get as much as a degree variance.
So is this my OCD raving, a bad gauge, or operator error?
What do you do? -
AuthorPosts