That’s wickedly kind of you, Clay!
I’ll send you the email tomorrow, but this time I want to pay for the shipping costs. Want that WE cap, too :-).
I am interested in the new style screws as well.
Maybe I will give Kyle a call Monday… If I can remember.
It is something I have been thinking about doing for awhile. Just not an absolute requirement.. I just use a small set of slip joint pliers if I need additions torque.
I do use the purple loktite on the set screws. I don’t have problems with them loosening.
BTW, so far so good with the ball joints and the plastic liner. I do use a synthetic oil with Teflon on the ball joints and keep them clean..
Phil
I too would like to get on the set screw request list? Could I email Kyle and give him my CC number?
Eamon,
A friendly bit of advice. Don’t send your CC number anywhere with unencrypted email.
Our Payment Card Industry certification will not even allow us to accept any card info by email. The risk of someone intercepting the info is too high.
[quote quote=“PhilipPasteur” post=11677]Eamon,
A friendly bit of advice. Don’t send your CC number anywhere with unencrypted email.
Our Payment Card Industry certification will not even allow us to accept any card info by email. The risk of someone intercepting the info is too high.[/quote]
Yeah your right Phil. I just wasn’t thinking, I was still drinking morning coffee :S
Also I guess I’m a bonehead, I just noticed after all this time the screws have a hex on them? I took out my hex wrench keys and I would think the going loose problem will be over?
I would be so lost without this forum!!:cheer:
You took the words right outta my keyboard. 
Eamon,
If you can snag some purple loctite You can find it on Amazon).. try some of that. It takes up any slop in the threads.. but is “breakable” . You will not need to tighten the set screws as much to make them stay put..
You took the words right outta my keyboard. :)[/quote]
We do agree quite often…
[quote quote=“PhilipPasteur” post=11689][quote quote=“cbwx34” post=11687]
You took the words right outta my keyboard. :)[/quote]
We do agree quite often…
;)[/quote]
'cept of course when you’re wrong… hehehe :evil:
I had the same problem but caught it the first time the threads were buggered up. I pulled the metal screws out and put in some nylon screws from Lowe’s that have a big head on them. then I tightened them down really good and have not moved them since. The friction of the nylon on the threads of the fine adjustment screw keep it really snug but not too tight as a lot of force is needed to turn the screw. Or if you like the screws that are on it you can place a 1/8" long piece of a small dowel or nylon rod in the screw hole and use that material as a cushion against your threads. Then use the original screws on top of that material to push it against the threads. Hope this helps some. This is the only modification I have done to my WEPS. I am also going to put some sort of cushion on the forward edge of my base so my rods do not chip my pretty stone base. I also plan on sharpening at my local Farmers Market with the possibility of the Flea Market and my local gun range too. Keep passing on your experience at your farmers market and hopefully everyone who wishes to do this can learn from one another.
Thank you
Jed
[quote quote=“cbwx34” post=11695][quote quote=“PhilipPasteur” post=11689][quote quote=“cbwx34” post=11687]
You took the words right outta my keyboard. :)[/quote]
We do agree quite often…
;)[/quote]
'cept of course when you’re wrong… hehehe :evil:[/quote]
That is what I said.. we agree almost all of the time…:woohoo:
[quote quote=“JedBowen” post=11727]I had the same problem but caught it the first time the threads were buggered up. I pulled the metal screws out and put in some nylon screws from Lowe’s that have a big head on them. then I tightened them down really good and have not moved them since. The friction of the nylon on the threads of the fine adjustment screw keep it really snug but not too tight as a lot of force is needed to turn the screw. Or if you like the screws that are on it you can place a 1/8" long piece of a small dowel or nylon rod in the screw hole and use that material as a cushion against your threads. Then use the original screws on top of that material to push it against the threads. Hope this helps some. This is the only modification I have done to my WEPS. I am also going to put some sort of cushion on the forward edge of my base so my rods do not chip my pretty stone base. I also plan on sharpening at my local Farmers Market with the possibility of the Flea Market and my local gun range too. Keep passing on your experience at your farmers market and hopefully everyone who wishes to do this can learn from one another.
Thank you
Jed[/quote]
Welcome to the forum.
Great post, thanks!
buggered up was the problem…B)
removed cleaned up - back in and still little tight in that one spot, but works ok.
.
.
.
.
.
Attachments:
Another alternative to Loctite especially if there are combinations of different metals is a sticky lube which is applied to the threads with a sort of mascara brush it is called Tef-Gel it is a corrosion eliminator it is a sticky white grease developed for the aeronautical & marine industries . I would only apply it to areas that do not see the light of day otherwise swarf will stick to it .I do not have my WE yet but where there is intent to use Loctite this is what is used more so plus it is not quite as messy as Loctite but if you want to get it off something use rags solvent do little to it .
Cleaning is the best maintenance for tools or machines and I would imagine that if you photograph and mark things with a Sharpie bag them up with labels and then possible clean with diesel and possible tooth brushes and dry off with rags and cotton buds or doweling with rags wrapped around then lightly grease areas where the fixings have to move & use the Tef-Gel for more permanent machine screws . Everything should go together beautifully then I would wipe away any visible grease with some alcohol so swarf does not collect .
Final note Tef-Gel is expensive but if you apply it carefully a syringe full of it lasts a long time and it does not dry out
I found something at Lowes. I cut off part of a plastic screw and put it in the hole of the setscrew so it acts as a buffer between the setscrew and the threads of the adjustment screw. It seems to work well