Re: Chosera Angles versus Diamond Angles?
Recent › Forums › Main Forum › Techniques and Sharpening Strategies › Chosera Angles versus Diamond Angles? › Re: Chosera Angles versus Diamond Angles?
The angle cube method is good. If you are more analytically inclined its a simple trig problem to work out the angle difference.Here is a table of results that applies when the stones are vertical, in line with the clamp.
Similar results can be calculated over the entire swing of the arms by considering how the blade edge intersects spheres
but I haven’t done that so far.
15.9415 15 r =0.6 h =0.25
21.2627 20 r =0.6 h =0.25
23.29 22 r =0.6 h =0.25
26.2572 25 r =0.6 h =0.25
31.3605 30 r =0.6 h =0.25
Here is an example of how to read this table.
r=.6 means half the thickness in unches of the hone. this is about .6″ fordiamond stones and .8 ” for shaptons.
h is the height of the sharp edge of the blade above the end of the clamp(not above the setting gauge). The six digit numbers are the calculated angle and the 2 digit numbers are the angle you set the rods to. so for example the calculated angle is 15.9415 degrees when the set angle is 15 degrees. (dont take the six digits seriously the accuracy of my measurements of the numbers is such that 3 digits at most are good.
the next table shows that the wicked edge sharpener is in fact calibrated for h=0.5 inch blade extension beyond the clamp since the calculated and set angles are quite close.
15.0572 15 r =0.6 h =0.5
20.141 20 r =0.6 h =0.5
22.0883 22 r =0.6 h =0.5
24.9499 25 r =0.6 h =0.5
29.9055 30 r =0.6 h =0.5
more blade extension tables :
Do[
14.2625 15 r= 0.6 h =0.75
19.1252 20 r= 0.6 h =0.75
20.9966 22 r= 0.6 h =0.75
23.7562 25 r= 0.6 h =0.75
28.5649 30 r= 0.6 h =0.75
13.5447 15 r =0.6 h =1.
18.2017 20 r =0.6 h =1.
20.0013 22 r =0.6 h =1.
22.6633 25 r =0.6 h =1.
27.3274 30 r =0.6 h =1.
12.8937 15 r =0.6 h =1.25
17.3593 20 r =0.6 h =1.25
19.0911 22 r =0.6 h =1.25
21.6599 25 r =0.6 h =1.25
26.1829 30 r =0.6 h =1.25
12.8937 15 r =0.6 h =1.5
17.3593 20 r =0.6 h =1.5
19.0911 22 r =0.6 h =1.5
21.6599 25 r =0.6 h =1.5
26.1829 30 r =0.6 h =1.5
11.7587 15 r =0.6 h =1.75
15.8798 20 r =0.6 h =1.75
17.4877 22 r =0.6 h =1.75
19.8836 25 r =0.6 h =1.75
24.1376 30 r =0.6 h =1.75
11.2613 15 r= 0.6 h =2.
15.2275 20 r= 0.6 h =2.
16.7787 22 r= 0.6 h =2.
19.0948 25 r= 0.6 h =2.
23.2216 30 r= 0.6 h =2.
the same tables for the shapton stones have r=0.8:
13.2112 15 r =0.8 h =0.25
18.6513 20 r =0.8 h =0.25
20.7288 22 r =0.8 h =0.25
23.7739 25 r =0.8 h =0.25
29.0233 30 r =0.8 h =0.25
12.4702 15 r =0.8 h =0.5
17.6558 20 r =0.8 h =0.5
19.6465 22 r =0.8 h =0.5
22.5759 25 r =0.8 h =0.5
27.6601 30 r =0.8 h =0.5
11.8054 15 r= 0.8 h =0.75
16.7559 20 r= 0.8 h =0.75
18.665 22 r= 0.8 h =0.75
21.4839 25 r= 0.8 h =0.75
26.4061 30 r= 0.8 h =0.75
11.2059 15 r =0.8 h =1.
15.939 20 r =0.8 h =1.
17.7715 22 r =0.8 h =1.
20.4855 25 r =0.8 h =1.
25.2501 30 r =0.8 h =1.
10.6629 15 r =0.8 h =1.25
15.1948 20 r =0.8 h =1.25
16.9554 22 r =0.8 h =1.25
19.5701 25 r =0.8 h =1.25
24.1823 30 r =0.8 h =1.25
10.6629 15 r =0.8 h =1.5
15.1948 20 r =0.8 h =1.5
16.9554 22 r =0.8 h =1.5
19.5701 25 r =0.8 h =1.5
24.1823 30 r =0.8 h =1.5
9.71766 15 r =0.8 h =1.75
13.89 20 r =0.8 h =1.75
15.5203 22 r =0.8 h =1.75
17.9523 25 r =0.8 h =1.75
22.2773 30 r =0.8 h =1.75
9.30401 15 r= 0.8 h =2.
13.3155 20 r= 0.8 h =2.
14.8866 22 r= 0.8 h =2.
17.2348 25 r= 0.8 h =2.
21.4254 30 r= 0.8 h =2.
For the gadget freaks consider using adjustable parallels to accurately set up the swing arms in a repeatable manner:
use calipers to repeatably set the adjustable paralles
to a precise width. Then use the adjustable parallel between the edge of the wicked edge base and the adjustable pivot.
A good usb microscpe is the ProScope HR2 withe the 30x lens.